My Future Programs (2010)
Space Frame Analysis and Design (Mero Systems)
Integrated With SAP 2000 V 14 (2010)
Created By : Bambang
Piscesa & Mudji Irmawan
ITS
MIX DESIGN With VRCPT + GA (Corrosion Environment) (2010)
Created By : Bambang
Piscesa & Mudji Irmawan
ITS
MIX DESIGN DOE Method (2010)
Created By : Bambang
Piscesa & Mudji Irmawan
My Current Programs
ITS
Strut And Tie Model Analysis VB.NET 2005 - (S2-ITS/2008)
Created By : Bambang
Piscesa & Tavio
This program was My Thesis in ITS, This program
could perform an optimization of STM Model through it's strength calculation to
find the optimal solution. It was started when I was wondering about the angle
of the STM and the deformation... well it was a lot of story to tell since this
program will be written for international journal, Hopefully it will be
accepted... =). This program still under development so only brief view will be
shown in the detailed preview.
ITS
Column Analysis 2009
Created By : Bambang
Piscesa & Mudji Irmawan
This program was the development of ITS Column Ver. 1.06 and
PiscesaCol Ver. 1.06, Now this program only can still performed the analysis of
rectangular concrete but with advanced features such as eleven kind of stress
strain relationship of confined concrete and four kind of stress strain
relationship. The reinforcement can be placed irregularly so any kind of
reinforcement shape can be analyzed. The confined stress strain relationship can
be applied to change the original ACI block stress to see the increasing in
strength of column concrete section with varied interaction diagram can be shown
and also this program can analyze the moment curvature of each stress strain
relationship.
ITS
Structure Analysis VB.NET 2005
-
(S2-ITS/2007)
Created By : Bambang
Piscesa
This program was written due to finish the Finite Element Method
Lecture in my master degree. This program was created with 3D Frame Analysis and
the load is applied as point load in structure element joint. The frame section
is shown as rectangular or other shape but the section property is still
manually configured. This program has been verified with SAP 2000 also with 3D
Frame Analysis. This program was written in Microsoft Visual Basic.Net 2005
Express and engine of the program is Written in MATLAB 7.1.
ITS
Response Spectrum 2007
-
(S2-ITS/2007)
Created By : Bambang
Piscesa & Dicky Imam Wahyudi
This program was written due to finish the Advanced Steel Structure
Lecture in my master degree. This program analyze the response spectrum of SDOF
structure with according Time History of Earth Quake. This program can analyze
the displacement, velocity, acceleration of elastic SDOF and inelastic SDOF. Can
show when the SDOF structure is yielding with varied ductility. This program was
written in Microsoft Visual Basic 6.0. In this program SDOF with varied damping
and the yielding of SDOF structure is shown.
ITS
MIX DESIGN ACI 211.1
-
(S2-ITS/2007)
Created By : Bambang Piscesa & Mudji Irmawan
This program was written to make the mix design calculation more
easier, this mix design calculation based on ACI Method Non-Air Entrained
Concrete. The program were written in Microsoft Visual Basic.Net 2008 Express,
and the engine of the program were written in Microsoft Visual C#.Net 2008
Express. Mix design of this program is including the use of Fly Ash as the
replacement of cement as the cementitious material and the use of water reducer
of any type according to the admixture vendor. In this program overview is shown
the mix design with fly ash and water reducer.
ITS
Column V1.06
-
(S2-ITS/2006)
Created By : Bambang
Piscesa
This program was the development of a new Piscesacol Ver 1.05, this
program was not completely finish because I had to continue my study in master
degree. The program were written in Microsoft Visual Basic.Net 2005. The main
purpose of this program is to analyzing the reinforced concrete section using
the Unified Method (ACI 318-2002) and using the Limit State Method (SNI
2847-2002 Or ACI 318-99). This program can analyze the rectangular section of
the column. In This Program Overview the rectangular reinforced concrete section
is analyzed.
PiscesaCol V1.05
-
(S1-ITS/2006)
Created By : Bambang Piscesa & Mudji Irmawan
& Iman Wimbadi
This program was the final project of my bachelor degree in civil
engineering, I had finished this program in about one month from scratch until
it’s done, this is the first time I learn about programming in Microsoft Visual
Basic 6.0. the main purpose of this program is to analyzing the reinforced
concrete section using the Unified Method (ACI 318-2002) and using the Limit
State Method (SNI 2847-2002 Or ACI 318-99). This program can analyze the
rectangular and circular section of the column including the slenderness effect
of column. For design the column concrete section this program can initialize
the interaction diagram for design where the reinforcement ratio is set from one
to eight percent. The slenderness information is more complete than other
programs. In This Program Overview the circle reinforced concrete section is
analyzed.